Request a quote for this product.
 

MIL-P-23377 ( MIL-P-23377H ) ( MIL P 23377 ) ( MIL-PRF-23377 ) is a two component, corrosion inhibiting, polyamide primer. This epoxy primer offers excellent corrosion and chemical resistance over properly prepared aluminum and steel substrates. This primer meets Type 1 (standard pigments), Class C (strontium chromate) and was designed to be topcoated with urethane or epoxy topcoats such as MIL-C-83286B, MIL-C-85285C or MIL-C-22750D or MIL-C-46168.

See product information sheet.

MIL-P-23377 ( MIL-P-23377G ) (MIL PRF 23377 ) is a two component, corrosion inhibiting, polyamide primer. This epoxy primer offers excellent corrosion and chemical resistance over properly prepared aluminum and steel substrates. This primer meets Type 1 (standard pigments), Class C (strontium chromate) and was designed to be topcoated with urethane or epoxy topcoats such as MIL-C-83286B, MIL-C-85285C or MIL-C-22750D.

TYPICAL PROPERTIES:

1. Color...................................Chromate Yellow
2. Solids by volume....................57%
3. Mix Ratio..............................4-1 by volume with part "B" catalyst
4. Dry Film Thickness..............   .9 mils (minimum)
5. Dry Times @77 F: - Tack Free 5hrs *
   - Dry 8 hrs *
   - Full Cure 7 days *
6. Recoat: - 1 hr. minimum *
   - 3 days maximum *
7. Pot Life @ 77 F.....................4 hrs.*
8. VOC (maximum)....................420 g/L
9. Shelf Life @ 77 F...................12 months ( D.M.)
10. Reducer...............................MIL-T-81772B ty 2
    (Reduction for conventional spray applic. 4-1-1)
11. S.F. Coverage......................1100 sq/ft gal. ***
    
    * times will vary with, humidity, temperature and film thickness.
    *** @ 100% transfer efficiency

MIXING - APPLICATION:

Mix primer part"A" 4-1 by volume with primer catalyst part"B". Stir thoroughly. Thin as needed with MIL-T-81772B ty2 reducer. Apply one full wet coat using 45-55 PSI ( conventional spray) at the gun. If a second coat is desired allow 10-15 minutes dry time between coats. Allow the final coat to dry a minimum of 1 hr. @77 F. Topcoat within 1-2 hours. If primer has been left to dry over 24 hours or has been baked, the surface must be abraded to achieve satisfactory adhesion. NOTE: Never "DRY SPRAY" primers, they need a wet coat to flow into conversion coatings and sand scratches. Refer to M.S.D.S. before use.

ADVANTAGES:

1. Corrosion Resistant.
2. Chemical Resistant.
3. Meets Military Specification.
4. Meets ASTM Standards.

SURFACE PREP & PRIMER (recommended):

1. Solvent wash.
2. Alumiprep- Etch & Clean.
3. Alodine- Chrome Conversion Coating.
4. Prime MIL-P-23377 @ .9 mils dry. (minimum).

For Aluminum -

See (mix ratio 4-1) product information sheet.

See (mix ratio 3-1) product information sheet.

MIL-P-23377 ( MIL-P-23377F ) ( MIL-PRF-23377 )is a two-component epoxy-polyamide coating for spray and brush applications. Suitable for use as a primer for aliphatic polyurethane topcoats. Furnished in a package kit and suitable for use under air pollution regulations. Formulated for the protection against solvents and chemicals on interior and exterior surfaces. Type11 use for low infrared reflective needs.

TYPICAL PROPERTIES:

1. Colours....................Yellow & Dark Green
2. Shelf Life................1 Year From Date Of Mfg.
3. Drying Time
       Set-To-Touch........Within 15-20 minutes
       Hour Hard Dry.........Within 6 hrs.
4. Pot Life..................8 hours
5. Gloss Value.............20 maximum

MIXING - REDUCTION:

Each of the two components should be thoroughly mixed separately. Component B is then slowly poured into component A with constant stirring until a one-to-one ratio is achieved. Mix components into the comp. A can and the comp. B can to intermix both components. Mix thoroughly and allow to stand one hour before using. Apply a mist coat and allow to dry 30 minutes. Apply a second coat to a total dry film thickness of 1.4 to 1.8 mils.

PRECAUTIONS:

• USE WITH ADEQUATE VENTILATION
• AVOID CONTACT WITH SKIN AND EYES
• READ MATERIAL SAFETY DATA SHEETS BEFORE USING
• KEEP OUT OF REACH OF CHILDREN
• FOR INDUSTRIAL USE ONLY

See product information sheet.

A fast dry, corrosion inhibiting, spray type lacquer primer for use over metal pre-treatment wash primer MIL-C-8514C.

PRODUCT DESCRIPTION:

A resin-acid type pre-treatment wash primer for use on metal surfaces of all types, but particularly effective on such surfaces as aluminum and cadmium plating where good adhesion is a problem. Its purpose is to increase the adhesion of the coating system and it should not be considered a permanent protective coating by itself. Green in colour.

MIXING-APPLICATION:

Mixing ratio by volume of 4 parts primer (resin component), one part acid component and 2 parts T-120-66 Thinner. Slight additional thinning may be done with T-120-66 but not with acid component. Pre-mix the acid component with T-120-66 Thinner then slowly stir this mixture in with the primer. Spray one thin semitransparent coat. Use mixed materials within 8 hours.

DRY TIMES:  Dry to topcoat in 15-30 minutes.

VOLUME SOLIDS:  9.5%

FOR PROFESSIONAL USE ONLY
PLEASE READ MATERIAL SAFETY DATA SHEETS

MIL-P-46105 is a single package, heat convertible/curing epoxy based, zinc-rich primer for use on ferrous metal surfaces prior to spot welding. Protects steel galvanically, thus preventing below film corrosion.

PRODUCT DESCRIPTION:

MIL-P-53022 Epoxy Polyamide ( MIL P 53022 ) ( MIL-P-53022B ) ( MIL-PRF-53022 ) is a two-component, flash dry, corrosion inhibiting lead and chromate-free epoxy primer. Can be used for ferrous and non-ferrous metals. This primer has a low Volatile Organic Compound (VOC) content and can be used to replace MIL-P-23377F and MIL-P-52192 where exposure to lead or chromate pigments is not acceptable. Supplied in a light gray colour approximate to #26622 of Fed.Std 595B.

TYPICAL PROPERTIES:

1. Colours....................Light Gray
2. Shelf Life................1 Year From Date Of Mfg.
3. Drying Time
       Set-To-Touch........Within 5 minutes.
       Hour Hard Dry.........Within 90 minutes.
4. Pot Life..................6 - 8 hours (77 Deg F)
5. Gloss Value.............30 maximum
6. Mixing Ratio............4 : 1

APPLICATION AND REDUCTION:

Each of the two components should be thoroughly mixed separately. Mix at a ratio of 4 parts Component A to 1 part Component B by volume. Mix thoroughly and allow to stand 30 minutes before using. Pot life is normally six to eight hours at 77 degrees Fahrenheit. Reduce with MIL-T-81772B Type 2 Thinner if required . Always read Material Safety Data Sheet before use.

PRECAUTIONS:

• USE WITH ADEQUATE VENTILATION
• AVOID CONTACT WITH SKIN AND EYES
• READ MATERIAL SAFETY DATA SHEETS BEFORE USING
• KEEP OUT OF REACH OF CHILDREN
• FOR INDUSTRIAL USE ONLY

See product information sheet.

MIL-P-53030 ( MIL-P-53030A ) ( MIL P 53030 ) ( MIL-PRF-53030 ) is a water reducible, air drying, corrosion inhibiting, epoxy type primer for pretreated ferrous and non-ferrous metals. The primer is lead and chromate free and is compatible with chemical agent resistant aliphatic polyurethane topcoats.

See product information sheet.

MIL-PRF-85582C ( MIL-PRF-85582 ) is a two-component chemically cured water-borne Epoxy Primer that forms a film that is resistant to chemicals, solvents, moisture and abrasion. This product has excellent adhesion to most substrates and is recommended for use as a primer under aliphatic polyurethane topcoats in aerospace applications. MIL-PRF-85582C epoxy primer is rust inhibitive and chemical resistant with excellent abrasion resistance.

See product information sheet.

A synthetic, rust-inhibiting, lacquer resisting primer coating.

For more information, please feel free to contact us.

A low moisture sensitive, corrosion inhibiting zinc chromate primer. Primarily intended for spray or dip on aluminum or magnesium surfaces coated with pre-treatment primer.

For spray, thin one part of primer with up to 2 ½ parts MIL-T-81772B, type 111, reducer. For dip, thin 3 parts to 5 parts.

Single wet coat dries dust free in 5 minutes. Tack free in 30 minutes.

40% Solids by Volume.

See product information sheet.

For more information on our aircraft MIL-SPEC coatings, aerospace coatings, and paint finishes, please feel free to
contact us.

Home
Aircraft Coatings    PPG Aerospace - PRC-DeSoto    PPG Aviation - Desothane    Strippers & Cleaners (Aviation)
Aerosol - Spray Can    Solid Film Lubricants    Automotive Coatings    Spray Equipment
Supplied Air Masks    How To Order    Contact Us

©Copyright Pacific Western Paints Ltd. 2002
Established in 1985, Pacific Western Paints has earned the trust and respect of customers locally and around the globe. We continue to do so by building our reputation by supplying the highest quality paint and spraying products for even the most demanding applications. At Pacific Western Paints, our approach to customer satisfaction makes a difference.

Quality Aircraft MIL-SPEC Coatings, Aerospace Coatings, and Paint Finishes.

Pacific Western Paints Ltd.
#205- 7188 Progress Way, Delta,
B.C., Canada, V4G 1M6

Tel: 604-432-6111 or 604-430-4151
or you can e-mail us at info@pwpaints.com